2-CH 10A DC Output Wireless Remote Control Receiver With Transmitter (Model: 0020426)

Regular price $46.00

Shipping calculated at checkout.

Application:
This 2 Channels wireless remote control switch kits with DC 6V 9V 12V 24V 10A input output radio receiver and RF transmitter.
This kit may be used in all types of industry automation, agriculture, home, factory, house, farm, vehicle, ship, offshore operations, etc. It can long range remote control DC electrical equipments, such as lamp, light, solar light, fan, motor, water pump, solenoid valve, door lock, gates, etc.

Feature:
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Four operating voltage versions: DC 6V, 9V, 12V, 24V optional.
DC Power Output: It can control DC equipment with voltage DC 6V, 9V, 12V or 24V.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.

Receiver Parameters:
Model No.: S2X-DC
Power Supply (Operating Voltage): DC6V (S2X-DC06), DC12V±1V (S2X-DC12), DC9V±1V (S2X-DC09), DC24V±1V (S2X-DC24), the operating voltage must be specified when ordering.
Output: DC6V (S2X-DC06), DC12V (S2X-DC12), DC9V (S2X-DC09), DC24V (S2X-DC24)
Channel: 2 CH
Quiescent Current: ≤6mA
Maximum Load Current of Relay: 10A / each channel
3 Control modes: Self-locking, Momentary, Interlocking
Working Frequency: 433.92 MHz
Wire Range of Terminals: 22-12AWG
Operating Temperature: -20°C ~ +70°C
PCB size: 88 x 80 x 18 mm (3.5 x 3.1 x 0.7 inches)
Case size: 115 x 90 x 55 mm (4.5 x 3.6 x 2.2 inches

Transmitter Parameters:
Model No.: 0021001 (C-2)
With Sliding Cover: Slide up when it doesn’t work (to protect the button). Slide down the button will appear.
Channel/Button: 2
Button Symbol: A, B
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 6mA
Operating Frequency: 433.92 MHz
Transmitting Distance: 100 metres / 300ft (theoretically)
Modulation Mode: ASK
Unit Size: 58mm x 39mm x 16mm

Matching Transmitters:
The receiver can work with different transmitters, such as model  C-2 (100 meters / 300 feet range)CP-2 (500 meters / 1500 feet range)CD-2 (Industrial, 1000 meters / 3000 feet range), or CB-2 (1000 meters / 3000 feet range).

Working Range:
With a transmitter (such as C-2) to form a complete set, the maximum working distance can reach 100 meters in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
IIf you need a longer working distance, you can replace the antenna on the receiver, or use an RF signal repeater, or use a powerful transmitter, such as a CB-2 transmitter.

Usage:
The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose the receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V version.

Setting different control modes:
1) Setting Self-locking mode (work with transmitter C-2): Press and hold the button of the receiver until signal LED flashes 3 times, then release button.
Press button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on.
Press button A again: The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.
Press button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.
Press button B again: The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.

2) Setting Momentary mode (work with transmitter C-2): Press and hold the button of receiver until signal LED flashes 2 times, then release button.
Press and hold button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on.
Release button A: The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.
Press and hold button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.
Release button B: The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.

3) Setting Interlocking mode (work with transmitter C-2): Press and hold the button of receiver until signal LED flashes 1 time, then release button.
Press button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on; The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.
Press button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.; The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.

Package Include:
1 x Receiver: S2X-DC-ANT3
2 x Transmitter: C-2
1 x User manual