1 Way 10A Wireless RF Remote Control Receiver Kit for DC 12V 24V Linear Actuator (Model: 0020603)

Regular price $52.00

Shipping calculated at checkout.

Application: 
Wireless Linear Actuator Remote Control Switch can be used for cars, lifting platforms, massage couches, electric beds, medical chairs, Kitchen appliance lifts,TV Lifts,electric lift desk, electric devices, micro-devices and so on. It can push, pull, lift and descend other devices.

Features:
Wireless remote control, easy to install.
Two operating voltage versions: DC 12V, 24V optional.
With limit control terminals: You can connect limit switches or sensors to restrict Linear Actuator Stroke.
You can remote control the electric linear actuator extension and retraction.
with the transmitter from any place within a reliable distance. 
You also can ccontrol the electric linear actuator extension and retraction by button on the receiver. 
With reverse power protection and over current protection.
The RF wireless signal can pass through walls, floors and doors.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Receiver Parameters:
Model No: S1F2-DC
Operating Voltage: 12±1VDC (model S1F2-DC12), or 24±2VDC (model S1F2-DC24), the operating voltage must be specified when ordering.
Channel: 1 CH, can work with 1 linear actuator 
Quiescent Current: ≤6mA
The Maximum Instantaneous Current of Starting Motor: 10A
Control Mode: Interlocking
Working Frequency: 433.92 MHz
Wire range for the terminals: 22-14AWG
Operating Temperature: -20 ° C to +70 ° C
Case size: 75mm x 54mm x 27mm

Matching Transmitters:
This receiver can work with different transmitters. Such as model CWC-3L (50M), or CB-3-2 (1000M) etc.

Transmitter Parameters:
Model No.: 0021101 (CWC-3L)
Waterproof
Channel/Button: 3
Button Symbol: ▲,▼, =
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 4mA
Operating Frequency: 433.92MHz
Transmitting Distance: 50m / 150ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 58mm x 30mm x 12mm

Working Range:
With a transmitter (such as CWC-3L) to form a complete set, the maximum working distance can reach 50M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as transmitter CB-3-2.

Setting different control modes:
1) Setting Interlocking mode: Connect JP1 or disconnect JP1&JP2
1-1) Function of transmitter CWC-3L:
Press button ▲ on remote: terminal “Output” output DC power, The electric linear actuator extends.
Press button ▼ on remote: terminal “Output” output DC power, The electric linear actuator retracts.
Press button =on remote: The electric linear actuator stops.

1-2) Function of manual buttons in receiver:
Press button K3 in receiver: terminal “Output” output DC power, The electric linear actuator extends.
Press button K1 in receiver: terminal “Output” output DC power, The electric linear actuator retracts.
Press button K2 in receiver: The electric linear actuator stops.

2) Setting Momentary mode: Connect JP2
2-1) Function of transmitter CWC-3L:
Press and hold button ▲ on remote: terminal “Output” output DC power, The electric linear actuator extends; Release button ▲: The electric linear actuator stops.
Press and hold button ▼ on remote: terminal “Output” output DC power, The electric linear actuator retracts; Release button ▼: The electric linear actuator stops.

2-2) Function of manual buttons in receiver:
Press and hold button K3 in receiver: terminal “Output” output DC power, The electric linear actuator extends; Release button K3: The electric linear actuator stops.
Press and hold button K1 in receiver: terminal “Output” output DC power, The electric linear actuator retracts; Release button K1The electric linear actuator stops.

Restrictive function:
You can connect two limit switches or sensors (normally close type) to terminals “X1” and “X2”, and then you can use limit switches or sensors to restrict Linear Actuator Stroke.
When the electric linear actuator extends, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.
When the electric linear actuator retracts, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.

Package Include:
1 x Receiver: S1F2-DC
2 x transmitter: CWC-3L
1 x User manual