Remote control switch kit with RF receiver and radio transmitter for wireless control the extension and retraction of electric linear actuator.
It can long range control the push, pull, lift and descend of electric linear actuators.
Widely used in cars, lifting platforms, massage couches, electric beds, medical chairs, Kitchen appliance lifts,TV Lifts,electric lift desk, electric devices, solar tracker, micro-devices and so on.
Wireless remote control, easy to install.
Two operating voltage versions: DC 12V, 24V optional.
With limit control terminals: You can connect limit switches or sensors to restrict Linear Actuator Stroke.
You can remote control the electric linear actuator extension and retraction.
with the transmitter from any place within a reliable distance.
You also can ccontrol the electric linear actuator extension and retraction by button on the receiver.
With reverse power protection and over current protection.
The RF wireless signal can pass through walls, floors and doors.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Linear Actuator Parameters:
Working voltage: DC 12V or DC 24V
Speed: 5mm ± 2mm/second, 10mm ± 3mm/second, 30mm ± 5mm/second.
Working current: 6A . You should choose a 10A power adapter to power this actuator, such as DC12V/10A (Model: 0010130) or DC24V/10A (Model: 0010140).
Shaft diameter: 24mm
Mounting holes diameter: 10mm
Environment temperature: -26℃ to 85℃
Noise level: lower than 42dB
IP rating: IP54
In-built limit switches prevents over-extending and over-compressing
|Stroke Length (mm)||50||100||150||200||250||300||350||400||450||500||600|
|Retracted Length (mm)||225||275||325||375||425||475||525||575||625||675||775|
|Extended Length (mm)||275||375||475||575||675||775||875||975||1075||1175||1375|
|Speed||5mm /seconde||10mm /seconde||30mm /seconde|
|Maximum load capacity||2000N / 400 lbs / 200 Kg||1000N / 200 lbs / 100Kg||500N / 100 lbs / 50 Kg|
Model No: S1PF3-DC
Operating Voltage: 12±1VDC (model S1PF3-DC12), or 24±2VDC (model S1PF3-DC24), the operating voltage must be specified when ordering.
Channel: 1 CH, can work with 1 linear actuator
Quiescent Current: ≤6mA
Rated Current: 15A
The Maximum Instantaneous Current of Starting Motor: 30A
Control Mode: Interlocking
Working Frequency: 433.92 MHz
Wire range for the terminals: 22-12 AWG
Operating Temperature: -20 ° C to +70 ° C
Case size: 100mm x 67mm x 39mm
This receiver can work with different transmitters. Such as model CWC-3L (50M), or CB-3-2 (1000M) etc.
Model No.: 0021101 (CWC-3L)
Button Symbol: ▲,▼, =
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 4mA
Operating Frequency: 433.92MHz
Transmitting Distance: 50m / 150ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 58mm x 30mm x 12mm
With a transmitter (such as CWC-3L) to form a complete set, the maximum working distance can reach 50M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as transmitter CB-3-2.
Function of transmitter:
Press button ▲ on remote: terminal “Output” output DC power, The electric linear actuator extends.
Press button ▼ on remote: terminal “Output” output DC power, The electric linear actuator retracts.
Press button =on remote: The electric linear actuator stops.
Function of manual buttons in receiver:
Press button K3 in receiver: terminal “Output” output DC power, The electric linear actuator extends.
Press button K1 in receiver: terminal “Output” output DC power, The electric linear actuator retracts.
Press button K2 in receiver: The electric linear actuator stops.
You can connect two limit switches or sensors (normally close type) to terminals “X1” and “X2”, and then you can use limit switches or sensors to restrict Linear Actuator Stroke.
When the electric linear actuator extends, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.
When the electric linear actuator retracts, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.
1 x Receiver: S1PF3-DC
2 x transmitter: CWC-3L
1 x Linear Actuator
2 x Mounting brackets
1 x User manual