Long Range 5 Km 8 Channels DC 9V 12V 24V Wireless Remote Control Switch Kit (Model: 0020055)

Regular price $115.00

Shipping calculated at checkout.

Application:
This long range 5000 meters 8 channels DC 9V 12V 24V 10A wireless remote control switch kit with radio receiver and RF transmitter.
The kit may be used in all types of industry automation, agriculture, home, factory, house, farm, vehicle, ship, offshore operations, etc. The kit can long distance control DC and AC equipments, such as remote control light, lamp, locks, motor, fans, pump, blinds, linear actuator, door, windows, electric solenoid valve, etc.

Feature:
Wireless control, easy to install.
Super long working range: With the transmitter forming a complete set, the maximum working distance may reach 5000 meters in an open area.
Wide operating voltage range: 9~28VDC
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.

Feedback Function:
The receiver and the transmitter have a Two-way working mode, so the user can know the working status of the receiver by the transmitter.
Two-way working mode: When the receiver is successfully triggered by the signal from the transmitter, it will immediately transmit a feedback signal to the transmitter, then the transmitter will send out a buzzing sound to inform you that the receiver has been successfully triggered.

Receiver Parameters:
Model No.: S8UW-DC
Operating Voltage: 9~28VDC
Working Frequency: 433.92 MHz
Quiescent Current: ≤10mA
Channel: 8 CH
Output Type: Dry Relays Output (Normally Open and Normally Closed)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 10A / each channel
Wire Range of Terminals: 22-12 AWG
3 Selectable Modes: Self-locking, Momentary, Interlocking
Operating Temperature: -20°C ~ +70°C
PCB size: 122 x 87 x 18 mm (4.8x 3.4 x 0.7 inches)
Case size: 145 x 90 x 40 mm (5.7 x 3.5 x 1.6 inches) 

Transmitter Parameters:
Model: 0021077 (CC-8)
Channel / Button: 8
Button Symbol: 1, 2, 3, 4, 5, 6, 7, 8
Operating Voltage: 9V (1 x 6F22-9V battery, can be used for 12 months)
Quiescent Current: 5μA
Working Current: 65mA (when the transmitter is transmitting the signal), 16mA( when the transmitter is receiving the signal).
Operating Frequency: 433.92 MHz
Modulation Mode: FSK + LORA
Feedback indication: buzzing sound
Transmitting Distance: 5000 meters / 15000 feet (theoretically)
With power switch on the side.
Operating Temperature: -20°C ~ +70°C
Unit Size: 135 x 42 x 25 mm (5.3 x 1.7 x 1.0 inches)

Working Range:
With the transmitter CC-8 forming a complete set, the maximum working distance may reach 5000 meters in an open area.
The maximum working distance is based on theoretical data which would be without barriers and without any RF interference. In practice, it will be hindered by trees, walls or other construction, and will be interfered with by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.

Setting different control modes:
1) Setting Self-locking mode: Connect two terminals M and T by the pin.
The operation of Self-locking mode with the transmitter CC-8: Press any button on the transmitter, the corresponding relay in the receiver is activated; Press the button again, the corresponding relay is deactivated. Such as the following,
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
Press the button 1 again: The relay 1 is deactivated, and the connected lamp 1 is turned off.
Press the button 2 on the transmitter: The relay 2 in the receiver is activated, and the connected lamp 2 is turned on.
Press the button 2 again: The relay 2 is deactivated, and the connected lamp 2 is turned off.
............
Press the button 8 on the transmitter: The relay 8 in the receiver is activated, and the connected lamp 8 is turned on.
Press the button 8 again: The relay 8 is deactivated, and the connected lamp 8 is turned off.

2) Setting Momentary mode: Do not connect any terminals.
The operation of Momentary mode with the transmitter CC-8: Press and hold any button on the transmitter, the corresponding relay in the receiver is activated; Release the button, the corresponding relay is deactivated. Such as the following,
Press and hold the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on.
Release the button 1: The relay 1 is deactivated, and the connected lamp 1 is turned off.
Press and hold the button 2 on the transmitter: The relay 2 in the receiver is activated, and the connected lamp 2 is turned on.
Release the button 2: The relay 2 is deactivated, and the connected lamp 2 is turned off.
............
Press and hold the button 8 on the transmitter: The relay 8 in the receiver is activated, and the connected lamp 8 is turned on.
Release the button 8: The relay 8 is deactivated, and the connected lamp 8 is turned off.

3) Setting Interlocking mode: Connect two terminals M and L by the pin.
The operation of Interlocking mode with the transmitter CC-8: Press any button on the transmitter, the corresponding relay in the receiver is activated and other all relays are deactivated. Such as the following,
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and the connected lamp 1 is turned on. 7 other relays are deactivated, and 7 other connected lamps are turned off.
Press the button 2 on the transmitter: The relay 2 in the receiver is activated, and the connected lamp 2 is turned on. 7 other relays are deactivated, and 7 other connected lamps are turned off.
.............
Press the button 8 on the transmitter: The relay 8 in the receiver is activated, and the connected lamp 8 is turned on. 7 other relays are deactivated, and 7 other connected lamps are turned off.

Package Include:
1 x Receiver: S8UW-DC-ANT3
1 x Transmitter: CC-8
1 x User manual