Note: This product should be used with four 12V 24V 6000N 600kg 1300lbs electric linear actuators B and four hall effect sensors (Model: 0043018).
Package Include:1 x Synchronous Controller (One-Control-Four, For 4 Linear Actuators B)
1 x Control Handle
1 x Remote Control (CP-2L)
1 x Power Cord
1 x User Manual
Note: Linear actuators and power supply are not included, please purchase separately.
Introduction:
If you want to use multiple linear actuators to raise and lower an equipment, for example two or four electric actuators. Since the high speed DC motors in electric actuators cannot run at exactly the same speed, so the movement speed of the electric actuator will also be different. When multiple electric actuators work at the same time, their actual speeds cannot be exactly the same. In this case, we can use a synchronous controller to operate multiple linear actuators to rise or fall synchronously. They work completely in sync without any difference.
Working principle:
If you want to use a synchronous controller to operate 2 or 4 linear actuators fully synchronously, you will need to add built-in Hall effect sensors to each linear actuator. And when you purchased Hall effect sensor along with linear actuator, we will install Hall effect sensor to linear actuator for you.
When 2 or 4 linear actuators are running together, Hall sensor will send Hall signals to the synchronization controller, and the controller will adjust the running speed of each linear actuator, so that all linear actuators run at the exact same speed.
Feature:
It can operate four electric linear actuators B to run completely synchronously.
Wired control via a control handle.
Wireless control via a remote.
Two function buttons: Up and Down.
With reset button.
Parameters:
Working Voltage: DC 12V or 24V
Working Frequency: 433.92 MHz
Working Distance: 100m / 300ft (theoretically)
Rated current: 20A
Case size: 150 x 147 x 40 mm (5.9 x 5.8 x 1.6 inches)
Operating Temperature: -20°C ~ +70°C
Connection:
1) Connect the positive pole of DC power supply to red power cord of the controller, and connect the negative pole of DC power supply to black power cord of the controller.
2) Plug four linear actuators to the controller.
3) Plug the control handle to the controller.
Operation via the control handle:
1) Press the button ▲ of the control handle, four linear actuators extend outward at the same time, they will reach the maximum stroke at the same time and stop automatically.
2) Press the button ▼ of the control handle, four linear actuators retract inward at the same time, they will fully retract at the same time and stop automatically.
3) During operation, you can also press any button to stop four linear actuators at the same time.
Operation via the remote control:
1) Press the button ▲ of the remote control, four linear actuators extend out at the same time, they will reach the maximum stroke at the same time and stop automatically.
2) Press the button ▼ of the remote control, four linear actuators retract inward at the same time, they will fully retract at the same time and stop automatically.
3) During operation, you can also press any button to stop four linear actuators at the same time.
Reset Function:
When this system has been running for a long time, if you find that they are no longer fully synchronized, you can reset the controller by following three methods.
Method 1: Press and hold two buttons of the control handle at the same time for more than 7 seconds.
Method 2: Press and hold the reset button of the controller and the button ▼ of the control handle at the same time for more than 7 seconds.
Method 3: Press and hold the reset button of the controller and the button ▼ of the remote control at the same time for more than 7 seconds.
How to pair the remote control to the controller:
Notice: We have paired the remote control to the controller before delivery.
Operation: Press the learning button on the controller for more than 3 seconds, then press any one button on the remote control.
How to delete the remote control:
Operation: Press the learning button on the controller, then press and hold the button ▼ of the remote control for more than 8 seconds.