Package Include:
1 x Receiver: S2XW-DC-ANT3
1 x User manual
Application:
For long range wireless remote control DC equipments, such as lamp, LED lighting, motor, solenoid valve, pump, electric lock, etc.
Feature:
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector; it can be installed outdoors.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
Feedback Function:
The receiver and the transmitter have a Two-way working mode, so the user can know the working status of the receiver by the transmitter.
Two-way working mode: When the receiver is successfully triggered by the signal from the transmitter, it will immediately transmit a feedback signal to the transmitter. When the transmitter receives this signal, it will send out a buzzing sound to inform you that the receiver has been successfully triggered.
Receiver Parameters:
Model: S2XW-DC-ANT3
Operating Voltage: 6VDC (model S2XW-DC06), or 9±1VDC (model S2XW-DC09), or 12±1VDC (model S2XW-DC12), or 24±2VDC (model S2XW-DC24)
Output Type: DC power supply output, same as input voltage.
Quiescent Current: ≤6mA
Maximum Load Current of Relay: 10A / channel
Channel: 2 CH
3 Selectable Working Modes: Self-locking, Momentary, Interlocking
Working Frequency: 433.92MHz
Operating Temperature: -20 °C ~ +70 °C
PCB size: 88 x 80 x 18 mm
Case size: 153 x 90 x 55 mm
Applicable Transmitters:
The receiver only works with 5000 meters transmitters, such as model CC-2 (5 km / 3 mi range) and CCW-2 (waterproof, 5 km / 3 mi range).
Super Long Working Range:
The receiver and the transmitter form a wireless remote control switch, the maximum working distance may reach 3mi or 5km in an open area.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no interference. But in the practice, it will be hindered by trees, walls or other construction, and will be interfered by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
Usage:
The receiver can be used to control DC 6V / 9V / 12V / 24V devices.
If the power supply of those equipments is DC 12V, you should choose the receiver with same DC 12V version.
If the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V version.
Wiring:
1) Connect the positive pole of DC power supply to input terminal “L/+” of the receiver;
2) Connect the negative pole of DC power supply to input terminal “N/-” of the receiver;
3) Connect the positive pole of DC device to output terminal “L/+” of the receiver;
4) Connect the negative pole of DC device to output terminal “N/-” of the receiver.
Setting different control modes:
1) Setting Self-locking mode (work with the transmitter CC-2): Turn on the third bit of the dip switch.
Press button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on.
Press button A again: The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.
Press button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.
Press button B again: The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.
2) Setting Momentary mode (work with the transmitter CC-2): Turn off the second bit and the third bit of the dip switch.
Press and hold button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on.
Release button A: The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.
Press and hold button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.
Release button B: The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.
3) Setting Interlocking mode (work with the transmitter CC-2): Turn on the second bit of the dip switch.
Press button A of the transmitter: The terminals "OUT1" of the receiver outputs DC power, and the connected lamp 1 is turned on; The terminals "OUT2" of the receiver stops outputting, and the connected lamp 2 is turned off.
Press button B of the transmitter: The terminals "OUT2" of the receiver outputs DC power, and the connected lamp 2 is turned on.; The terminals "OUT1" of the receiver stops outputting, and the connected lamp 1 is turned off.