Package Include:
1 x Receiver: S2PXW-DC-ANT3
1 x Transmitter: CC-2 or CCW-2
1 x User manual
Application:
For long range wireless remote control DC equipments, such as lamp, LED lighting, motor, solenoid valve, pump, electric lock, heater, etc.
Feature:
Waterproof: The receiver has waterproof case and waterproof connector; it can be installed outdoors.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
Feedback Function:
The receiver and the transmitter have a Two-way working mode, so the user can know the working status of the receiver by the transmitter.
Two-way working mode: When the receiver is successfully triggered by the signal from the transmitter, it will immediately transmit a feedback signal to the transmitter. When the transmitter receives this signal, it will send out a buzzing sound to inform you that the receiver has been successfully triggered.
Receiver Parameters:
Model: S2PXW-DC-ANT3
Operating Voltage: Compatible with DC 10V~80V
Output Type: DC power output, same as the input voltage.
Channel: 2 Way
3 Selectable Working Modes: Self-locking, Momentary, Interlocking
Quiescent Current: ≤6mA
Maximum Load Current of Relay: 30A per channel
Working Frequency: 433MHz
Operating Temperature: -20°C ~ +70°C
PCB size: 88 x 80 x 18 mm
Case size: 153 x 90 x 55 mm
Transmitter Parameters:
Model: 0021061 (CC-2)
Channel / Button: 2
Button Symbol: A, B
Operating Voltage: 9V (1 x 6F22-9V battery)
Operating Frequency: 433MHz
Modulation Mode: FSK + LORA
Feedback indication: buzzing sound
Transmitting Distance: 5000 meters / 15000 feet (theoretically)
Unit Size: 135 x 42 x 25 mm
Applicable Transmitters:
The receiver only works with 5000 meters transmitters, such as model CC-2 (5000 meters / 15000 ft range) and CCW-2 (waterproof, 5000 meters / 15000 ft range).
Working Range:
The kit has a maximum working distance of 5km (3mi) in open areas.
The maximum working distance is based on theoretical data which would be without barriers and without any RF interference. In practice, it will be hindered by trees, walls or other construction, and will be interfered with by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
Wiring:
1) Connect the positive pole of the DC device to the output terminal "L/+" of the receiver;
2) Connect the negative pole of the DC device to the output terminal "N/-" of the receiver;
3) Connect the positive pole of the DC power supply to the input terminal "L/+" of the receiver;
4) Connect the negative pole of the DC power supply to the input terminal "N/-" of the receiver.
Setting different control modes:
1) Setting Self-locking mode: Turn on the third bit of the dip switch.
The operation of Self-locking mode with the transmitter CC-2:
Press the button A on the transmitter: The DC device connected to the receiver terminals "OUTPUT1" is turned on.
Press the button A again: The DC device connected to the receiver terminals "OUTPUT1" is turned off.
Press the button B on the transmitter: The DC device connected to the receiver terminals "OUTPUT2" is turned on.
Press the button B again: The DC device connected to the receiver terminals "OUTPUT2" is turned off.
2) Setting Momentary mode: Turn off the second bit and the third bit of the dip switch.
The operation of Momentary mode with the transmitter CC-2:
Press and hold the button A on the transmitter: The DC device connected to the receiver terminals "OUTPUT1" is turned on.
Release the button A: The DC device connected to the receiver terminals "OUTPUT1" is turned off.
Press and hold the button B on the transmitter: The DC device connected to the receiver terminals "OUTPUT2" is turned on.
Release the button B: The DC device connected to the receiver terminals "OUTPUT2" is turned off.
3) Setting Interlocking mode: Turn on the second bit of the dip switch.
The operation of Interlocking mode with the transmitter CC-2:
Press the button A on the transmitter: The DC device connected to the receiver terminals "OUTPUT1" is turned on; The DC device connected to the terminals "OUTPUT2" of the receiver is turned off.
Press the button B on the transmitter: The DC device connected to the receiver terminals "OUTPUT2" is turned on; The DC device connected to the terminals "OUTPUT1" of the receiver is turned off.