Package Include:
1 x Receiver: S12UW-DC-ANT3
1 x Transmitter: CC-12
1 x User manual
Application:
For long range control DC and AC equipments, such as lamp, LED lighting, motor, solenoid valve, pump, electric lock, etc.
Feature:
Wireless control, easy to install.
Relay Output: This receiver is dry relay output; it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
With working mode display screen: Different numbers on the LED screen correspond to different working modes.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
Wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
The receiver has reverse voltage protection and overcurrent protection.
The receiver can only be triggered by paired transmitters.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.
Feedback Function:
The receiver and the transmitter have a Two-way working mode, so the user can know the working status of the receiver by the transmitter.
Two-way working mode: When the receiver is successfully triggered by the signal from the transmitter, it will immediately transmit a feedback signal to the transmitter. When the transmitter receives this signal, it will send out a buzzing sound to inform you that the receiver has been successfully triggered.
Receiver Parameters:
Model: S12UW-DC-ANT3
Operating Voltage: 12~24VDC
Output Type: Dry Relays Output (With Normally Open and Normally Closed Terminals)
Maximum Load Current of Relay: 10A / channel
Quiescent Current: ≤10mA
Channel: 12 CH
8 Different Control Modes: Self-locking, Momentary, Interlocking, and 5 Mixed modes
Working Frequency: 433.92 MHz
Operating Temperature: -20 °C ~ +70 °C
PCB size: 122 x 87 x 18 mm
Case size: 145 x 90 x 40 mm
Transmitter Parameters:
Model: 0021078 (CC-12)
Channel / Button: 12
Button Symbol: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12
Operating Voltage: 9V (1 x 6F22-9V battery)
Quiescent Current: 5μA
Working Current: 65mA (when the transmitter is transmitting the signal), 16mA( when the transmitter is receiving the signal).
Operating Frequency: 433.92 MHz
Modulation Mode: FSK + LORA
Feedback indication: buzzing sound
Transmitting Distance: 5000 meters / 15000 feet (theoretically)
With power switch on the side.
Operating Temperature: -20°C ~ +70°C
Unit Size: 135 x 42 x 25 mm (5.3 x 1.7 x 1.0 inches)
Suitable Transmitters:
This receiver only works with 5000 meters transmitter CC-12 (5 km / 3 mi range).
Working Range:
The kit has a maximum working distance of 5,000 meters in open areas.
The maximum working distance is based on theoretical data which would be without barriers and without any RF interference. In practice, it will be hindered by trees, walls or other construction, and will be interfered with by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
Wiring:
1) If you want to control a DC 12V lamp, do as following:
1.1 Connect the positive pole of DC power supply 1 to terminal <VCC> of the receiver.
1.2 Connect the negative pole of DC power supply 1 to terminal <GND>of the receiver.
1.3 Connect the positive pole of DC power supply 2 to terminal <NO> of the receiver.
1.4 Connect the positive pole of DC lamp to terminal <COM> of the receiver.
1.5 Connect the negative pole of DC power supply 2 to the negative pole of DC lamp.
2) If you want to control an AC 220V lamp, do as following:
2.1 Connect the positive pole of DC power supply to terminal <VCC> of the receiver.
2.2 Connect the negative pole of DC power supply to terminal <GND>of the receiver.
2.3 Connect the live wire of AC power supply to terminal <NO> of the receiver.
2.4 Connect one side of AC lamp to terminal <COM> of the receiver.
2.5 Connect the neutral wire of AC power supply to another side of AC lamp.
Switch the working mode or switch the number of operating channels:
The receiver has two buttons, button A is the channel number switching button, and button B is the working mode switching button.
1) When the receiver is powered on, the LED screen will display "A12".
2) If you press and hold the button A for 2-3 seconds, the LED screen will flash, and the receiver enters the channel number switching status. At this time, you may press the button A to switch the display text of the LED screen. The text will switch from A12 to A06 then to A08. A12 indicates that all 12 channels of the receiver are operational. A06 indicates that only 6 channels of the receiver are operational. A08 indicates that only 8 channels of the receiver are operational. If you again press and hold the button A for 2-3 seconds, the LED screen stops flashing, and the receiver exits the channel number switching status.
3) If you press and hold the button B for 2-3 seconds, the LED screen will flash, and the receiver enters the working mode switching status. At this time, you may press the button B to switch the display text of the LED screen. The text will switch from b01 to b08. Different numbers correspond to different working modes. If you again press and hold the button B for 2-3 seconds, the LED screen stops flashing, and the receiver exits the working mode switching status.
Setting different working modes:
1) Setting Momentary mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b01".
The operation of Momentary mode with the transmitter CC-12:
Press and hold the button 1 on the transmitter: The relay 1 in the receiver is activated; Release the button 1: The relay 1 is deactivated.
Press and hold the button 2 on the transmitter: The relay 2 in the receiver is activated; Release the button 2: The relay 2 is deactivated.
............
Press and hold the button 12 on the transmitter: The relay 12 in the receiver is activated; Release the button 12: The relay 12 is deactivated.
2) Setting Self-locking mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b02".
The operation of Self-locking mode with the transmitter CC-12:
Press the button 1 on the transmitter: The relay 1 in the receiver is activated; Press the button 1 again: The relay 1 is deactivated.
Press the button 2 on the transmitter: The relay 2 in the receiver is activated; Press the button 2 again: The relay 2 is deactivated.
............
Press the button 12 on the transmitter: The relay 12 in the receiver is activated; Press the button 12 again: The relay 12 is deactivated.
3) Setting Interlocking mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b03".
The operation of Interlocking mode with the transmitter CC-12:
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and other 11 relays are deactivated.
Press the button 2 on the transmitter: The relay 2 in the receiver is activated, and other 11 relays are deactivated.
............
Press the button 12 on the transmitter: The relay 12 in the receiver is activated, and other 11 relays are deactivated.
4) Setting Momentary (Channels 1~6) + Self-locking (Channels 7~12) mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b04".
5) Setting Momentary (Channels 1~6) + Interlocking (Channels 7~12) mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b05".
6) Setting Self-locking (Channels 1~6) + Interlocking (Channels 7~12) mode: When the receiver is in the working mode switching state, press button B until the LED screen displays "b06".
7) Setting Special Interlocking mode (Every two channels form a special interlocking mode): When the receiver is in the working mode switching state, press button B until the LED screen displays "b07".
Press the button 1 on the transmitter: The relay 1 in the receiver is activated, and the relay 2 is deactivated.
Press the button 1 again: The relay 1 is deactivated.
Press the button 2 on the transmitter: The relay 2 in the receiver is activated, and the relay 1 is deactivated.
Press the button 2 again: The relay 2 is deactivated.
............
8) Setting dual button control single channel mode (Each two buttons on the transmitter controls one channel. This mode supports up to 6 channels, the other 6 channels are not used.): When the receiver is in the working mode switching state, press button B until the LED screen displays "b08".
Press the button 1 on the transmitter: The relay 1 in the receiver is activated; Press the button 2: The relay 1 is deactivated.
Press the button 3 on the transmitter: The relay 2 in the receiver is activated; Press the button 4: The relay 2 is deactivated.
............
Press the button 11 on the transmitter: The relay 6 in the receiver is activated; Press the button 12: The relay 6 is deactivated.
How to set the feedback function:
You can turn on the fourth bit of the dip switch to activate the feedback function; or turn off the fourth bit to deactivate the feedback function.