If you want a complete 12V solar power kit, for wireless receiver. Please click here to buy.
Package Include:
1 x Receiver: S1PUW-DC12-ANT3
1 x Transmitter: CC-2
1 x Transmitter: CC-2N-2
2 x Water Level Sensors
1 x User manual
Working Principle:
Transmitter CC-2N-2 is a special remote control with normally open contact trigger. It has 3 input terminals (COM, Signal 1, Signal 2) for connecting two devices with normally open contact, such as warning host, detectors, sensors, limit switches, Programmable Logic Controllers and so on.
This transmitter can be combined with different types of long range 5000 meters receivers to form a wireless control system, and this system is used to wirelessly control the device A through the device B with normally open contact.
Application:
You can connect two water level sensors to this transmitter, and connect the water pump to the receiver, then the pump will automatically work according to the water level.
When the water reaches the low water level, the water level sensor 1 is triggered, the transmitter automatically emits a wireless signal "ON".
When the receiver receives this wireless signal, it will turn on the pump motor to pump water into the tank.
When the water reaches the high water level, the water level sensor 2 is triggered, the transmitter automatically emits a wireless signal "OFF". When the receiver receives this wireless signal, it will turn off the pump motor to stop pumping water.
Feature:
Wireless control, easy to install.
Super long working range: With the transmitter forming a complete set, the maximum working distance may reach 5000 meters in an open area.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
High Power: Each channel can work at maximum load current 30A.
With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.
Feedback function:
The receiver and the transmitter have a Two-way working mode, and the user can know the working status of receiver by the transmitter in such a long distance.
Two-way working mode: When you press the transmitter to send RF signal to the receiver, if the receiver has been successfully triggered or operated, the receiver will immediately transmit a RF feedback signal to the transmitter. Then the transmitter will send out a buzzing sound to inform you that the receiver has been successfully operated.
Receiver:
Model No.: S1PUW-DC12
Operating Voltage: 12±1VDC
Working Frequency: 433.92 MHz
Quiescent Current: ≤6mA
Channel: 1 CH
Output Type: Dry Relays Output (Normally Open and Normally Closed)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 30A / each channel
Wire Range of Terminals: 22-12 AWG
3 Selectable Modes: Self-locking, Momentary, Interlocking
Operating Temperature: -20°C ~ +70°C
PCB size: 140 x 73 x 18 mm (5.5 x 2.9 x 0.7 inches)
Case size: 192 x 100 x 45 mm (7.6 x 4.0 x 1.8 inches)
Transmitters:
Model No.: CC-2
Channel / Button: 2
Operating Voltage: 9V (1 x 6F22 -9V battery, can be used for 12 months)
Quiescent Current: 5μA
Working Current: 65mA (when the transmitter is transmitting the signal), 16mA (when the transmitter is receiving the signal).
Operating Frequency: 433.92 MHz
Modulation Mode: FSK+LORA
Feedback indication: buzzing sound
Transmitting Distance: 5000 meters / 15000ft (theoretically)
With power switch on the side.
Operating Temperature: -20°C to +70°C
Unit Size: 135mm x 42mm x 25mm
Model No.: CC-2N-2
With 3 trigger terminals (COM, Signal 1 and Signal 2)
Triggering method: When terminal "Signal 1" and terminal "COM" are connected, it will send wireless signal "ON". When terminal "Signal 2" and terminal "COM" are connected, it will send wireless signal "OFF".
With two buttons: red button and black button
Operating Voltage: 12V (12V Rechargeable Lithium Battery)
Quiescent Current: 3mA
Working Current: 50~80mA
Operating Frequency: 433.92MHz
Modulation Mode: FSK+LORA
Feedback indication: buzzing sound
Transmitting Distance: 5000 meters / 15000ft (theoretically)
With waterproof case and external antenna.
With power switch on the side.
Operating Temperature: -20°C to +70°C
Unit Size: 178mm x 120mm x 60mm
Water Level Sensor:
Body Material: PP
Float Material: PP
Operating Temperature: -10°C to +85°C
Maximum Voltage: DC 100V
Maximum Current: 0.5A
Maximum Power: 10W
Working Range:
The maximum working distance can reach 5000 meters in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
Usage:
1. Installation:
1) Put the water level sensor 1 downwards and install at the low water level position in the tank; Put the water level sensor 2 upwards and install at the high water level position in the tank.
2) Connect the water level sensor 1 to terminals "Signal 1" and "COM" of transmitter CC-2N-2.
3) Connect the water level sensor 2 to terminals "Signal 2" and "COM" of transmitter CC-2N-2.
4) Connect the positive pole of the DC power supply to the receiver's terminal "L / +" and terminal B
5) Connect the negative pole of DC power supply to the receiver's terminal "N / -". and the negative pole of the DC pump
6) Connect the positive pole of the DC pump to the receiver's terminal A
2. Operation:
1) Control pump by transmitter CC-2:
Press button A of the transmitter CC-2, the relay of receiver is activated, and the pump is turned on.
Press button B of the transmitter CC-2, the relay of receiver is deactivated, and the pump is turned off.
2) Automatically control pump by transmitter CC-2N-2 & Water Level Sensors:
When the water reaches the low water level, two wires of the water level sensor 1 is connected, the transmitter CC-2N-2 automatically emits a wireless signal "ON", which is equivalent to the function of the red button on the transmitter. When the receiver receives this wireless signal, it will turn on the pump motor to pump water into the tank.
When the water reaches the high water level, two wires of the water level sensor 2 is connected, the transmitter CC-2N-2 automatically emits a wireless signal "OFF", which is equivalent to the function of the black button on the transmitter. When the receiver receives this wireless signal, it will turn off the pump motor to stop pumping water.
You also can press red button or black button on the transmitter to turn on / off the pump.
