Package Include:
1 x Receiver: S1PUW-AC-ANT3
1 x User manualÂ
Application:
For long range wireless remote control AC or DC equipment, such as lamp, LED lighting, motor, solenoid valve, pump, electric lock, etc.
Feature:
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Universal input: Support 110V AC (100V~120V) used in US, CA, etc, and 220V AC (200V~240V) used in DE, UK, FR, etc.
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
With external antenna, the receiver has a farther working range.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
Feedback Function:
The receiver and the transmitter have a Two-way working mode, so the user can know the working status of the receiver by the transmitter.
Two-way working mode: When the receiver is successfully triggered by the signal from the transmitter, it will immediately transmit a feedback signal to the transmitter, then the transmitter will send out a buzzing sound to inform you that the receiver has been successfully triggered.
Receiver Parameters:
Model No.: S1PUW-AC-ANT3
Operating Voltage: Compatible with AC 100V~240V
Output Type: Dry Relays Output (Normally Open and Normally Closed)
Quiescent Current: ≤6mA
Maximum Load Current of Relay: 30A
Channel: 1 CH
3 Selectable Modes: Self-locking, Momentary, Interlocking
Working Frequency: 433.92MHz
Operating Temperature: -20°C ~ +70°C
PCB size: 88 x 80 x 18 mm
Case size: 153 x 90 x 55 mm
Matching Transmitters:
The receiver only works with 5000 meters transmitters.
When you set the receiver in Self-locking mode or Momentary mode, it should work with single button transmitter, such as model CC-1 (5000 meters/15000 ft range) and CCW-1 (waterproof, 5000 meters/15000 ft range).
When you set the receiver in Interlocking mode, it should work with two buttons transmitter, such as model CC-2 (5000 meters / 15000 ft range) and CCW-2 (waterproof, 5000 meters / 15000 ft range).
Working Range:
With the transmitter (such as CC-2) forming a complete set, the maximum working distance may reach 5000 meters in an open area.
The maximum working distance is based on theoretical data which would be without barriers and without any RF interference. In practice, it will be hindered by trees, walls or other construction, and will be interfered with by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
Wiring:
I) If you want to control a DC lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L/+” of the receiver;
2) Connect the neutral wire of AC power supply to terminal “N/-” of the receiver;
3) Connect the positive pole of DC power supply to terminal “NO” of the receiver;
4) Connect the negative pole of DC power supply to the negative pole of DC lamp;
5) Connect the positive pole of DC lamp to terminal “COM” of the receiver.
II) If you want to control an AC 120V or 220V lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L/+” of the receiver;
2) Connect the neutral wire of AC power supply to terminal “N/-” of the receiver;
3) Connect the live wire of AC power supply to terminal “NO” of the receiver;
4) Connect the neutral wire of AC power supply to one side of AC lamp;
5) Connect another side of AC lamp to terminal “COM” of the receiver.
Setting different control modes:
1) Setting Self-locking mode: Turn on the third bit of the dip switch.
The operation of Self-locking mode with the transmitter CC-1:
Press the button on the transmitter: The relay in the receiver is activated, and the connected lamp is turned on.
Press the button again: The relay is deactivated, and the connected lamp is turned off.
2) Setting Momentary mode: Turn off the second bit and the third bit of the dip switch.
The operation of Momentary mode with the transmitter CC-1:
Press and hold the button on the transmitter: The relay in the receiver is activated, and the connected lamp is turned on.
Release the button: The relay is deactivated, and the connected lamp is turned off.
3) Setting Interlocking mode: Turn on the second bit of the dip switch.
The operation of Interlocking mode with the transmitter CC-2:
Press the button A on the transmitter: The relay in the receiver is activated, and the connected lamp is turned on.
Press the button B on the transmitter: The relay is deactivated, and the connected lamp is turned off.