Wireless Remote Control Time Delay Switch Receiver For DC Motor (Model: 0020087)

Regular price $55.00

Shipping calculated at checkout.

Package Include:
1 x Receiver: S1PFD-DC
1 x User manual

Application:
This 7V~27V wireless remote control time delay switch receiver.
For long range control DC electric motor to rotate clockwise, counterclockwise and stop.

Feature:
Wireless control, easy to install.
Suitable for DC motor.
DC 7~27V operating voltage range.
You can operate the motor to rotate in positive or reversal direction by the transmitter.
With working mode setting button: 5 different working modes can be switched.
With LED display screen: The LED screen will display the working mode and working time.
With time delay function: You can set the forward and reverse working time of DC motor. When you operate the motor to run, the motor will stop automatically after the set delay time.
With wired control terminals: You can connect manual switches to control the motor.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors, or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.

Receiver Parameters:
Model: S1PFD-DC
Operating Voltage: DC 7~27V
Output Type: DC 7~27V (The output voltage is the same as the input voltage)
Quiescent Current: ≤6mA
Rated Current: 30A, so motor maximum starting current cannot exceed 30A.
5 Selectable Working Modes: Delay working mode, Single signal trigger delay working mode, Automatic cycle working mode, Momentary, Self-locking
Working Frequency: 433.92 MHz
Suitable Wires for Connecting Terminals: 22-12 AWG
Operating Temperature: -20°C ~ +70°C
PCB size: 93 x 88 x 24 mm
Case size: 104 x 89 x 40 mm

Suitable transmitters:
The receiver can work with different transmitters, such as model CP-3 (500 meters / 1500 feet range), CG-3 (wall mounted, 500 meters / 1500 feet range), and CB-3-2 (1000 meters / 3000 feet range).

Working Range:
With a transmitter (such as CP-3) to form a complete set, the maximum working distance can reach 500 Meter in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can use a high-power transmitter, such as CB-3-2 transmitter.

Usage:
The receiver can be used to control DC 7~27V motor.

Wiring:
1) Connect two wires of DC motor to output terminals <MOTOR> of the receiver, and you can exchange these two wires to change the rotating direction of motor.
2) Connect the positive pole of DC power supply to input terminal <+> of the receiver.
3) Connect the negative pole of DC power supply to input terminal <-> of the receiver.

How to set different working modes:
The receiver will be set in "P--1" Delay working mode before leaving the factory, if you want to use another mode, please follow the following steps.
The receiver has four buttons, button K1 is the setting button, and buttons K2, K3, and K4 are delay time adjustment buttons.

When the receiver is powered on, the LED screen lights up. If you press and hold the button K1 for 2-3 seconds, the LED screen will display "P--1", and the receiver enters the working mode setting. At this time, you may press the button K2 or K3 to switch the display text of the LED screen, different text on the LED screen correspond to different working modes. The text can be switched from "P--1" to "P--6".
"P--1" means delay working mode.
"P--2" means single signal trigger delay working mode.
"P--3" means automatic cycle working mode.
"P--4" means momentary working mode.
"P--5" means self-locking working mode.
"P--6" working mode is useless.
Notice: When the receiver is operating in "P--1", "P--2" or "P--3" working mode, you will need to set the corresponding delay time.

1. Setting delay working mode:
When the receiver is in the working mode setting state, press the button K2 or K3 to switch the display text until the LED screen displays "P--1".

How to set the delay time:
1) After setting the "P--1" working mode, press the K1 button again to enter the setting of the forward working time, and the LED screen will display "A001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
2) Press the K1 button again to enter the setting of the reverse working time, and the LED screen will display "b001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
3) After setting the delay times, press the K1 button again to exit the setting state.

The operation by the transmitter, such as CP-3:
1) Press the button ▲ on the transmitter: DC motor rotates in positive direction; After the forward working time, DC motor automatically stops. During the working time, you can also press the button ■ to immediately stop DC motor.
2) Press the button ▼ on the transmitter: DC motor rotates in reversal direction; After the reverse working time, DC motor automatically stops. During the working time, you can also press the button ■ to immediately stop DC motor.

2. Setting single signal trigger delay working mode:
When the receiver is in the working mode setting state, press the button K2 or K3 to switch the display text until the LED screen displays "P--2".

How to set the delay time:
1) After setting the "P--2" working mode, press the K1 button again to enter the setting of the forward working time, and the LED screen will display "A001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
2) Press the K1 button again to enter the setting of the waiting time, and the LED screen will display "b001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
3) Press the K1 button again to enter the setting of the reverse working time, and the LED screen will display "C001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
4) After setting the delay times, press the K1 button again to exit the setting state.

The operation by the transmitter, such as CP-3:
1) Press the button ▲ on the transmitter: DC motor rotates in positive direction; After the forward working time, DC motor automatically stops. During the working time, you can also press the button ■ to immediately stop DC motor.
2) After the waiting time, DC motor automatically rotates in reversal direction; After the reverse working time, DC motor automatically stops. During the working time, you can also press the button ■ to immediately stop DC motor.

3. Setting automatic cycle working mode:
When the receiver is in the working mode setting state, press the button K2 or K3 to switch the display text until the LED screen displays "P--3". (The power of the receiver needs to be restarted after switching from other operating modes to the auto-cycle working mode.)

How to set the delay time:
1) After setting the "P--3" working mode, press the K1 button again to enter the setting of the forward working time, and the LED screen will display "A001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
2) Press the K1 button again to enter the setting of the waiting time, and the LED screen will display "b001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
3) Press the K1 button again to enter the setting of the reverse working time, and the LED screen will display "C001". At this time, you can press the K2 button to increases the delay time, or press the K3 button to reduce the delay time, or press the K4 button to set the position of the decimal point.
4) After setting the delay times, press the K1 button again to exit the setting state.

The operation by the transmitter, such as CP-3:
1) After the automatic cycle working mode is set, DC motor will automatically rotate in positive direction; After the forward working time, DC motor automatically stops.
2) After the waiting time, DC motor automatically rotates in reversal direction; After the reverse working time, DC motor automatically stops.
3) After the waiting time, DC motor automatically rotates in positive direction again. In this way, the DC motor will keep working in a loop.
4) At any time, you can press the button on the transmitter to stop the cycle working.
Notice: During the cyclic working, if you press the button to stop the cycle working, you need to restart the power supply to start the cycle working again.

The meaning of the decimal point when it is in different positions:
When there is no decimal point, it means that the delay time is seconds. For example, “A002” means 2 seconds.
When the decimal point is in the first position, it means that the delay time is minutes. For example, “A002.” means 2 minutes.
When the decimal point is in the third position, it means that the delay time is 0.01 second. For example, “A0.02” means 0.02 seconds.
When the decimal point is in the second position, it means that the delay time is 0.1 second. For example, “A00.2” means 0.2 seconds.

4. Setting Momentary mode:
When the receiver is in the working mode setting state, press the button K2 or K3 to switch the display text until the LED screen displays "P--4".

The operation by the transmitter, such as CP-3:
1) Press and hold the button ▲ on the transmitter: DC motor rotates in positive direction; Release the button ▲, DC motor stops.
2) Press and hold the button ▼ on the transmitter: DC motor rotates in reversal direction; Release the button ▼, DC motor stops.

5. Setting Self-locking mode:
When the receiver is in the working mode setting state, press the button K2 or K3 to switch the display text until the LED screen displays "P--5".

The operation by the transmitter, such as CP-3:
1) Press the button ▲ on the transmitter: DC motor rotates in positive direction; Press the button ▲ again or press the button■, DC motor stops.
2) Press the button ▼ on the transmitter: DC motor rotates in reversal direction; Press the button ▼ again or press the button ■, DC motor stops.

Wired control terminals:
The receiver has wired control terminals, and you can connect external devices (with normally open contact), sensors, or manual switches to these terminals, then use them to operate the motor.
For example, you can connect three manual switches to wired control terminals <->, and according to following wiring diagram.
The operation of the manual switch in different working modes is the same as that of the transmitter.

How to pair the transmitter to the receiver:
1) Press the learning button in the receiver for 1- 2 seconds, the signal LED in the receiver turns on, this indicates that the receiver enters the learning state.
2) First press the button ▲ on the transmitter, the signal LED will flash once. Then press the button ■ on the transmitter, the signal LED will flash once. Finally press the button ▼ on the transmitter, the signal LED will flash once. This indicates that the pairing with three buttons is successful.
3) The receiver can learn several transmitters with different codes.

How to delete all transmitters codes stored in the receiver:
Press and hold the learning button in the receiver for 9-10 seconds, the signal LED lights up, then flashes three times quickly and then goes out, at this time release the learning button, this indicates that all stored codes have been successfully deleted.