Package Include:
1 x Receiver: S2U-AC380
1 x User manual
Application:
For long range wireless remote control AC DC equipments,such as lamp, light, LED lighting, motor, solenoid valve, pump, fan, heater, etc.
Feature:
Wireless control, easy to install.
Universal Power Supply: AC 75~400V, support AC 110V, AC 120V, AC 220V, AC 240V, AC 380V.
Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminals are NO (normally open), which serves as a switch. That means you should also connect a separate power supply to equipments.
With 3 manual buttons: You can press the manual buttons to control the equipments.
With external telescopic antenna, the receiver have a farther working range.
You can control the equipments by using the receiver with transmitter (remote control) from any place within a reliable distance.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No.: S2U-AC380
Power Supply (Operating Voltage): AC 75~400V (110V/120V/220V/240V/380V)
Output: Relay output (Normally open)
Channel: 2 CH
Control Modes: Self-locking, Momentary, Interlocking
Static Current: ≤6mA
Maximum Load Current: 10 A / each channel
Working Frequency: 433MHz
Wire range for the terminals: 22-12 AWG
Operating Temperature: -20 ° C to +70 ° C
Case size: 115 x 78 x 40 mm
Applicable Transmitters:
The receiver can work with different transmitters, such as CP-2 (500 metres), CD-2 (industrial, waterproof, 1000 metres) and CB-3 (1000 metres).
Working Range:
This receiver and different transmitters form a complete set, which can achieve different working distances. For example, when it and the transmitter CP-2 form a complete set, the maximum working distance may reach 1500 feet or 500 meters in an open area. When it and the transmitter CB-3 or CD-2 form a complete set, the maximum working distance may reach 3000 feet or 1000 meters in an open area.
The maximum working distance is based on theoretical data without obstacles and any RF interference. In practice, it will be hindered by trees, walls, or other construction, and will be interfered with by other wireless signals. Therefore, the actual working distance may not reach this maximum distance.
Usage:
The receiver can be used to control both 0~28VDC and AC 100~450V equipment.
Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Two terminals are Normally Open.
It can be used directly in single-phase AC equipments and DC equipments.
It cannot be used directly with three-phase electrical equipment; it must be used in conjunction with an AC contactor.
Setting different control modes:
1) Setting Self-locking mode: When the receiver is in the status of LEARNING, press button A or 1 of the transmitter CP-2 or CD-2 or CB-3.
The operation of Self-locking mode with the transmitter CP-2 or CD-2:
Press button A or 1 on the transmitter or button A or 1 on the receiver: The relay 1 is activated, and the contactor 1 is connected, the equipment 1 works.
Press button A or 1 on the transmitter or button A or 1 on the receiver again: The relay 1 is deactivated, and the contactor 1 is disconnected, the equipment 1 stops working.
Press button B or 2 on the transmitter or button B or 2 on the receiver: The relay 2 is activated, and the contactor 2 is connected, the equipment 2 works.
Press button B or 2 on the transmitter or button B or 2 on the receiver again: The relay 2 is deactivated, and the contactor 2 is disconnected, the equipment 2 stops working.
2) Setting Momentary mode: When the receiver is in the status of LEARNING, press button B or 2 of the transmitter CP-2 or CD-2 or CB-3.
The operation of Momentary mode with the transmitter CP-2 or CD-2:
Press and hold button A or 1 on the transmitter or button A or 1 on the receiver: The relay 1 is deactivated, and the contactor 1 is connected, the equipment 1 works.
Release button A or 1 on the transmitter or button A or 1 on the receiver: The relay 1 is deactivated, and the contactor 1 is disconnected, the equipment 1 stops working.
Press and hold button B or 2 on the transmitter or button B or 2 on the receiver: The relay 2 is activated, and the contactor 2 is connected, the equipment 2 works.
Release button B or 2 on the transmitter or button B or 2 on the receiver: The relay 2 is deactivated, and the contactor 2 is disconnected, the equipment 2 stops working.
3) Setting Interlocking mode: When the receiver is in the status of LEARNING, press button C of the transmitter CB-3.
The operation of Interlocking mode with the transmitter CB-3:
Press button A on the transmitter or button A on the receiver: The relay 1 is deactivated, and the contactor 1 is connected, the equipment 1 works.
Press button C on the transmitter or button "STOP" on the receiver: The relay 1 is deactivated, and the contactor 1 is disconnected, the equipment 1 stops working.
Press button B on the transmitter or button B on the receiver: The relay 2 is activated, and the contactor 2 is connected, the equipment 2 works.
Press button C on the transmitter or button "STOP" on the receiver: The relay 2 is deactivated, and the contactor 2 is disconnected, the equipment 2 stops working.