1 Channel DC 12V 10A Remote Control Receiver Kit with Electric Gear Motor (Model: 0020579)

Regular price $61.00

Shipping calculated at checkout.

Application:
This is a DC motor wireless remote control switch kit, with 12V motor, radio receiver, and RF transmitter.
It can long range remote control DC motor positive rotation or reverse rotation.
Widely used in rolling blinds, rolling doors, projection screens, awnings, conveyors, toy cars, etc.

Features:
Wireless remote control, easy to install.
Operating voltage versions: DC 12V.
You can remote control DC motor positive rotation, reverse rotation or stop rotation with the transmitter from any place within a reliable distance.
You also can control DC motor positive rotation, reverse rotation or stop rotation by button on the receiver.
With reverse power protection and over current protection.
The RF wireless signal can pass through walls, floors and doors.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Receiver Parameters:
Model No: S1FU-DC
Operating Voltage: 12±1VDC (model S1FU-DC12)
Control Mode: Momentary and Interlocking
Working Frequency: 433.92 MHz
Quiescent Current: ≤6mA
Wire range for the terminals: 22-14 AWG
Channel: 1 CH, can work with 1 DC motor
Maximum Working Current: 10A / each channel, so motor's maximum starting current can not exceed 10A.
Operating Temperature: -20 ° C to +70 ° C
PCB size: 67mm x 50mm x 18mm
Case size: 75mm x 54mm x 27mm

Transmitter Parameters:
Model No.: 0021004 (C-3-2)
With Sliding Cover: Slide up when it doesn’t work (to protect the button). Slide down the button will appear.
Channel/Button: 3
Button Symbol: ▲, ▼, ■
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 6mA
Operating Frequency: 433.92MHz
Transmitting Distance: 100m / 300ft (theoretically)
If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Modulation Mode: ASK
Unit Size: 58mm x 39mm x 16mm

DC Motor Parameters:
Nominal voltage: 12V DC
Operating voltage range: 3 - 18V DC
Diameter: 37mm
Length (excluding shaft): 92.5mm
Total length: 119mm
Shaft length: 15.5mm
Shaft diameter: 6mm
Front panel 3.0mm Screw for fixing this motor
Optional no-load speed at 12V:16RPM,32RPM,54RPM,100RPM,295RPM,868RPM,2000RPM.

 No-load speed at 12V  16RPM    32RPM    54RPM    100RPM    295RPM    868RPM    2000RPM  
 No-load current (A) 1.6 1.6 1.6 1.6 1.6 1.6 1.6
 Load speed (RPM) 14 27 46 85 250 738 1600
 Load current (A) 1.5 1.5 1.5 1.5 2 2.5 3
 Operating torque (kg.cm) 60 50 45 40 12 8 5
 Stall torque (kg.cm) 260 230 180 150 80 50 26
 Stall current (A) 7 7 7 7 7 7 7
 Gear ratio 1:973 1:505 1:305 1:168 1:56 1:19 1:8


Matching Transmitters:
This receiver can work with different transmitters. such as model C-3-2 (100 meters), or CB-3-2 (1000 meters) etc.

Working Range:
With a transmitter (such as C-3-2) to form a complete set, the maximum working distance can reach 100 meters in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you need a longer working distance, you can replace the antenna on the receiver, or use an RF signal repeater, or use a powerful transmitter, such as a CB-3-2 transmitter.

Setting different control modes:
1) Setting Interlocking mode: Disconnect Jumper-1 and Jumper-2.
Mode Interlocking (working with transmitter C-3-2):
Press button ▲ of transmitter: Motor rotates in positive direction.
Press button ▼ of transmitter: Motor rotates in reversal direction.
Press button ■ of transmitter: Motor stops.

2) Setting Momentary mode: Only connect Jumper-1
Mode Momentary (working with transmitter C-3-2):
Press and hold button ▲ of transmitter: Motor rotates in positive direction. Release button ▲ of transmitter: Motor stops.
Press and hold button ▼ of transmitter: Motor rotates in reversal direction. Release button ▼ of transmitter: Motor stops

Package Include:
1 x Receiver: S1FU-DC12
2 x Transmitter: C-3-2
1 x DC Motor
1 x User manual