1 CH 10A 12V 24V Remote Control Switch Kit for Linear Actuator (Model: 0020317)

Regular price $48.00

Shipping calculated at checkout.

Application:
Wireless Linear Actuator Remote Control Switch can be used for cars, lifting platforms, massage couches, electric beds, medical chairs, Kitchen appliance lifts,TV Lifts,electric lift desk, electric devices, micro-devices and so on. It can push, pull, lift and descend other devices.

Features:
Wireless remote control, easy to install.
Wide operating voltage range: 12~36VDC
With limit control terminals: You can connect limit switches or sensors to restrict Linear Actuator Stroke.
With wired control terminals: You can connect manual switches to control the electric linear actuator extension and retraction
You can remote control the electric linear actuator extension and retraction.
with the transmitter from any place within a reliable distance.
You also can ccontrol the electric linear actuator extension and retraction by button on the receiver.
With reverse power protection and over current protection.
The RF wireless signal can pass through walls, floors and doors.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Receiver Parameters:
Model No: S1FC-DC12
Control Mode: Momentary and Interlocking
Power Supply (Operating Voltage): DC12V~36V
Output: DC12V~36V
Working Frequency: 433.92MHz
Channel: 1 CH, can work with 1 Linear Actuator
Static Current: ≤6mA
Maximum Working Current: 10A / each channel, so Linear Actuator's maximum starting current can not exceed 10A.
PCB Size: 94mm x 56mm x 24mm
Case Size: 100mm x 60.5mm x 30mm

Transmitter Parameters:
Model No.: 0021050 (CV-2-2) / 0021051 (CV-4-2)
Channel/Button: 2 (CV-2-2) / 4 (CV-4-2)
Button Symbol: ▲, ▼ (CV-2-2)/▲, ▼, Two■ (CV-4-2)
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 15mA
Operating Frequency: 433.92MHz
Transmitting Distance: 500m / 1500ft (theoretically)
If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 110mm x 50mm x 18mm

Matching Transmitters:
This receiver can work with different transmitters. When you set the receiver in momentary mode, it should work with two button transmitters, such as model C-2L-2 (100M), CV-2-2 (500M), or CB-2 (1000M) etc. When you set the receiver in Interlocking mode, it should work with three/four button transmitters, such as model C-3-2 (100M), CV-4-2 (500M), or CB-3-2 (1000M) etc.

Working Range:
With a transmitter (such as CV-4-2) to form a complete set, the maximum working distance can reach 500M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters.

Setting different control modes:
1) Setting Interlocking mode (with transmitter CV-4-2): Connect Jumper 3&4
1-1) Button of receiver:
Press button “UP” of receiver: The electric linear actuator extends.
Press button “DOWN” of receiver: The electric linear actuator retracts.
Press button “STOP” of receiver: The electric linear actuator stops.

1-2) Button of transmitter (with transmitter CV-4-2):
Press button ▲ of transmitter: The electric linear actuator extends.
Press button ▼ of transmitter: The electric linear actuator retracts.
Press button ■ of transmitter: The electric linear actuator stops.

2) Setting Momentary mode (with transmitter CV-2-2): Connect Jumper 1&2
2-1) Button of receiver:
Press and hold button “UP” of receiver: The electric linear actuator extends. Release button “UP” of receiver: The electric linear actuator stops.
Press and hold button “DOWN” of receiver: The electric linear actuator retracts. Release button “DOWN” of receiver: The electric linear actuator stops.

2-2) Button of transmitter (with transmitter CV-2-2):
Press and hold button ▲ of transmitter: The electric linear actuator extends. Release button ▲ of transmitter: The electric linear actuator stops.
Press and hold button ▼ of transmitter: The electric linear actuator retracts. Release button ▼ of transmitter: The electric linear actuator stops

Limit control terminals:
Limit control terminals TOPR, COM and TOPL are normally close, you can connect limit switches or sensors (normally close type) to TOPR, COM and TOPL, and then you can use limit switches or sensors to restrict Linear Actuator Stroke.
When the electric linear actuator extends, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.
When the electric linear actuator retracts, if the actuator collides with the external limit switch, the electric linear actuator will stop automatically.

Wired control terminals:
You can connect manual switches to terminals “COM”, “UP”, “DOWN”, “STOP”, then you can use manual switches to control the electric linear actuator extension and retraction.
1) Control mode Interlocking
When connect terminals “UP” and “COM”, the electric linear actuator extends. And when connect “STOP” and “COM”, the electric linear actuator stops.
When connect terminals “DOWN” and “COM”, the electric linear actuator retracts. And when connect “STOP” and “COM”, the electric linear actuator stops.
2) Control mode Momentary
When connect terminals “UP” and “COM”, the electric linear actuator extends. And when disconnect “UP” and “COM”, the electric linear actuator stops.
When connect terminals “DOWN” and “COM”, the electric linear actuator retracts. And when disconnect “DOWN” and “COM”, the electric linear actuator stops.

Package Include:
1 x Receiver: S1FC-DC12
1 x transmitter: CV-2-2 or CV-4-2
1 x User manual