Package Include:
1 x Receiver: S1DA-AC
1 x User manual
Application:
It can long range remote control DC or AC equipments, such as lamp, LED lighting, motor, solenoid valve, pump, electric lock, fan, heater, etc.
Feature:
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Universal input: Support 110V AC (100V~120V) used in US, Canada, etc, and 220V AC (200V~240V) used in Germany, UK, France, etc.
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipment. The output terminals are NO / NC (normally open / normally closed), serving as a switch.
With adjustable 0 seconds to 99 hours time delay off function.
The transmitter / remote can control the receiver from any place within a reliable working distance.
The wireless RF signal from the transmitter can pass through walls, floors, doors or windows, but it will lose some operating range.
The receiver has reverse power protection and over current protection built in.
The receiver only works with the selected transmitter which is matched to the receiver.
One or more transmitters / remotes can control one or several receivers simultaneously.
Two or more receivers may be used in the same area.
Receiver Parameters:
Model No.: S1DA-AC
Operating Voltage: AC100~240V (110V/120V/220V/240V)
Output Type: Dry Relays Output (Normally Open and Normally Closed)
Maximum Load Voltage of Relay: 240VAC or 28VDC
Maximum Load Current of Relay: 10A
Quiescent Current: ≤6mA
Channel: 1 CH
Working Frequency: 433.92 MHz
Control Mode: Delay (Press -> ON; Then OFF after the delay time)
Wire Range of Terminals: 22-12AWG
Operating Temperature: -20°C ~ +70°C
PCB size: 140 x 73 x 18 mm
Case size: 192 x 100 x 45 mm
Suitable Transmitters:
The receiver can work with different transmitters. such as model C-2 (100 meters / 300 feet range), CP-2 (500 meters / 1500 feet range), CD-2 (Industrial, 1000 meters / 3000 feet range), and CB-2 (1000 meters / 3000 feet range).
Working Range:
With a transmitter (such as C-2) to form a complete set, the maximum working distance can reach 100M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can use a powerful transmitter, such as CD-2 or CB-2 transmitter.
Usage:
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals A and B are Normally Closed.
Wiring:
1) If you want to control a DC device, do as following:
1-1) Connect the live wire of AC power supply to terminal "L/+" of the receiver;
1-2) Connect the neutral wire of AC power supply to terminal "N/-" of the receiver;
1-3) Connect the positive pole of DC power supply to terminal "C" of the receiver;
1-4) Connect the negative pole of DC power supply to terminal the negative pole of DC device;
1-5) Connect the positive pole of DC device to terminal "B" of the receiver.
2) If you want to control an AC device, do as following:
2-1) Connect the live wire of AC power supply to terminal "L/+" of the receiver;
2-2) Connect the neutral wire of AC power supply to terminal "N/-" of the receiver;
2-3) Connect the live wire of AC power supply to terminal "C" of the receiver;
2-4) Connect the neutral wire of AC power supply to one side of AC device;
2-5) Connect the another side of AC device to terminal "B" of the receiver.
Operation (with the transmitter C-2):
Press the button A on the transmitter: The relay in the receiver is activated, and the connected device works.
After delay time (or press the button B on the transmitter): The relay is deactivated, and the connected device stops working.
Setting the delay time:
Press buttons of “＋” and “－” on the timer of the receiver, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second.
For example, if you set “S 0 1”, it means the delay time is 1 second.